Our Professional Clear Gloss Lacquer has been specially formulated to produce a deep gloss finish for interior or exterior projects in just two to four coats.

Dry and handleable in 10 to 20 minutes under normal conditions, it is possible to produce glass-like finishes within hours of application. Drying time may vary depending on ambient temperature and humidity.

For a simple gloss finish, two coats will generally be enough over a properly sealed surface. Use our Professional Sealer Spray for best results. For a glass-like finish, we recommend at least four coats and then polish with pastes and creams.

Overcoat with our Microcrystalline Wax for a smooth feeling and fingerprint resistant top coat. Use in combination with our Intrinsic Colour Collection, sealers, oils and waxes to create your own finishing regime.

Basic Application:
This lacquer will produce a high strength gloss finish. These are the basic steps to get started.
– Sand your work down to at least 400 grit and ensure surface is free from dust, grease and moisture;
– Prepare the surface with a suitable sealer and ensure it has fully dried.
– Shake can with the cap on for at least two minutes before use. Protect lathe and surfaces;
– Avoid breathing spray – Use appropriate PPE and use in a well ventilated area;
– Apply light coats 200mm from the piece, giving time for the lacquer to dry between coats. Two to four coats is usually sufficient;
– Lightly cut back the lacquer between dry coats for an even finish;
– Under normal conditions, this Professional Lacquer can be mechanically buffed in under 3 hours.
– For a glass-like finish, use abrasive pastes and creams according to manufacturers instructions.

This Professional Clear Satin Lacquer produces a silky feeling, hard wearing finish in just two coats on most wooden surfaces.
Dry and handleable in 10 to 20 minutes, it is possible to finish elegant pieces in under an hour. Drying time may vary depending on ambient temperature and humidity.
Two good coats of this satin lacquer should be enough to provide a suitably solid finish on most wooden surfaces. It will conform to grain and texture patterns exceptionally well without hiding them.
Apply some of the Intrinsic Colour Collection dyes to your work before using this to produce an elegantly coloured and finished piece.
For the best possible finish, always ensure that the surface you are applying it to is perfectly smooth, free from dust, scratches and properly sealed.

Basic Application:
When used correctly, this lacquer will produce a high strength satin finish that feels silky smooth to the touch. These are the steps we recommend to get started.
– Sand your work down smooth to at least 400 grit and ensure surface is free from dust, grease and moisture;
– Prepare the surface well with a suitable sealer and ensure it has fully dried. For best results, use our Pro Matt Sealer Spray and follow those instructions;
– Shake can with the cap on for at least two minutes before use;
– Avoid breathing spray. Use in a well ventilated area and wear appropriate PPE. Protect lathe and surfaces;
– Apply light coats 200mm from the piece, giving time for the lacquer to dry between coats;
– Lightly cut the lacquer back between dry coats for an even finish. Leave the final alone;
– Apply a coat or two of our Microcrystalline Wax for a fingerprint resistant overcoat.

This professional grade Black Gloss Lacquer has been formulated to produce a deep black gloss finish in just two coats on most wooden surfaces.
Dry and handleable in 10 to 20 minutes under normal conditions, it is possible to produce glass-like finishes within hours of application. Drying time may vary depending on ambient temperature and humidity.
For a simple gloss finish, two coats will generally be enough over a properly sealed surface. Use our Microcrystalline Wax for a fingerprint resistant over coat.
For a glass-like finish, we recommend four coats and then polish with pastes and creams.
Apply two coats onto open grained woods like ash or woods with added texture and use our embellishing waxes over the top when dry to enhance the remaining grain or textured pattern.

Basic Application:
This deep black lacquer will produce a high strength gloss finish. These are the steps we recommend to get started.
– Sand your work down smooth to at least 400 grit and ensure surface is free from dust, grease and moisture;
– Prepare the surface well with a suitable sealer and ensure it has fully dried. We recommend our Pro Spray Sealer when using this product;
– Shake can with the cap on for at least two minutes before use. Protect lathe and surfaces;
– Avoid breathing spray – Use appropriate PPE and use in a well ventilated area;
– Apply light coats 200mm from the piece, giving time for the lacquer to dry between coats. Two coats is usually sufficient;
– Under normal conditions, this Professional Lacquer can be mechanically buffed in under 3 hours.
– For a glass-like finish, use abrasive pastes and creams according to manufacturers instructions.

Our Professional Black Satin Lacquer produces a silky feeling, solid black finish in just two coats on most wooden surfaces.
Dry and handleable in 10 to 20 minutes, it is possible to finish elegant pieces in under an hour. Drying time may vary depending on ambient temperature and humidity.
Two suitable coats of this satin lacquer should be enough to provide a suitable solid finish on most wooden surfaces. It will conform to grain and texture patterns exceptionally well, without hiding them.
Imaginative use of this product, combined with the others across the Hampshire Sheen range will give you plenty of design and creative options.
For the best possible finish, always ensure that the surface you are applying it to is perfectly smooth, free from dust, scratches and properly sealed.

Basic Application:
When used correctly, this lacquer will produce a high strength satin finish that feels silky smooth to the touch. These are the steps we recommend to get started.
– Sand your work down smooth to at least 400 grit and ensure surface is free from dust, grease and moisture;
– Prepare the surface well with a suitable sealer and ensure it has fully dried. We recommend our Pro Spray Sealer when using this product;
– Shake can with the cap on for at least two minutes before use. Protect lathe and surfaces;
– Avoid breathing spray – Use appropriate PPE and use in a well ventilated area;
– Apply light coats 200mm from the piece, giving time for the lacquer to dry between coats. Two coats is usually sufficient;
– Adding an overcoat of Hampshire Sheen Microcrystalline Wax will provide the piece fingerprint resistance without unduly increasing the level of shine.

Our Professional Matt Cellulose Sanding Sealer Spray can be used on a variety of surfaces, not just wood. It has been formulated for us to produce a tough surface for our finishes to adhere to.
Non-darkening, the spray is ideal for use over applied colours like the Intrinsic Colour Collection. Without having to wipe or brush on the sealer, you can be sure there will be no further bleeding or blending of the colours.
Dry in 5 – 15 minutes, this product works best when cut back, or lightly sanded either between coats, or after the final coat for a smooth surface to accept your final finish. Drying time may vary depending on ambient temperature and humidity.
One or two coats of the Pro Matt Sanding Sealer spray is generally enough to seal the wood. More or fewer coats may be required depending on the porosity of the piece you are working on.

Basic Application:
This is the method we recommended for using our Professional Matt Sanding Sealer Spray for an even surface before final finishing.
– Sand your work down smooth to at least 400 grit and ensure surface is free from dust, grease and moisture. Clean the grain of dust if using (for example, ash);
– Shake can with the cap on for at least two minutes before use;
– Use appropriate PPE and apply in a well ventilated area. Protect lathe and surfaces;
– Using steady passes holding the can 200mm from the surface, apply an even coat;
– Once dry, we recommend lightly cutting back the surface for a smoother surface before applying subsequent coats;
– Apply a second coat of sealer and repeat above steps until surface is evenly coated;
– Before applying your final finish, lightly cut back the sealer once more to a create a smooth surface.